How to do the assembly of the bed with your own hands, step by step recommendations

In order to create a comfortable atmosphere in the room and give the interior an original look, it is necessary to acquire compact and stylish furniture. A bed with a lifting device may well serve as such a furniture accessory. Built-in niches allow you to compactly put in them bed linen and other accessories. It would seem that it is rather difficult to assemble such a bulky design. In fact, assembling a bed does not take much time. This type of furniture is practically no different from other types of stationary beds. The main difference is the lifting mechanism, which is installed to raise the berth above the base in order to open a roomy space for storing things.

Where to start

Purchasing upholstered bedroom furniture, most of us are wondering how to assemble a bed ourselves and where to start? Before performing work on the assembly of the structure, you should figure out which tool will be needed to carry out such work.

In any furniture product, there are always bolts, screws, nuts. Therefore, you can not do without a set of screwdrivers and ring spanners. It will not be superfluous to have a screwdriver with various nozzles. In modern models, furniture manufacturers have recently begun to use the Euroscrew with countersunk head and hexagon inside. In order to avoid misunderstandings, you should think about such a specific tool. So that the design of the bed as a result does not look like a curve, furniture assembly should be done using a level and a tape measure.

An instruction must be attached to the product without fail, which describes in detail how to assemble a bed. It is better to familiarize yourself with it in advance.

If the decision is made, and yet we assemble the bed with our own hands, the most necessary tools, without which it is impossible to perform the work qualitatively, we can consider

  • A set of screwdrivers or a screwdriver;
  • Spanners;
  • Hexagon for furniture screws;
  • Roulette and level.

Build nuances

If you look, the whole procedure for assembling a bed with a lifting mechanism is no different from assembling a regular bed, except for installing a lift in the form of a spring device or a gas lift. If you carefully follow the instructions, then there will be no problems.

An experienced craftsman can assemble a bed in a very short time. A person who has taken up such work for the first time may encounter some complications, namely:

  • On the legs or on the back of the headboard there may be blind holes for fastening with screws. These holes simply need to be drilled for future use;
  • The lifting mechanism may be disassembled. Before installing it, it is necessary to assemble it, which is quite difficult for a person without experience;
  • Panels and partitions may not have markup, which will also complicate the work.

If the instructions are still not at hand, the Internet will always come to the rescue, on the network of which you can find any information of interest. The websites provide a sufficient amount of manuals on how to assemble a single bed and a double bed; the assembly of the dolphin bed and the eurobook system is described step by step. In fact, all these and many other representatives of upholstered furniture differ only in the appearance and method of attachment of transforming mechanisms.

Base

At the initial stage, they begin to assemble the base, on which the soft mattress of the bed will be located. The base is a box, the walls of which are laminated chipboards. Between themselves, they are fastened with durable metal corners using self-tapping screws. In most cases, the panels already have special holes for furniture Euro screws, which are tightly tightened with a special hexagon screwdriver.

Around the perimeter of the resulting structure is fixed base for an orthopedic mattress. The base itself is made of two rows of lamellas - curved panels. The lamellas are responsible for the orthopedic properties of the bed and bear the burden of the mattress and the weight of the person lying on it. Due to their curved shape, the lamellas do not creak or make other sounds unpleasant to the hearing. Significantly extend the life of the bed due to the fact that they take the main burden on themselves. It is customary to install at least 15 lamellas on one single bed, and more than 30 samples go on a double bed.

Make the frameWe connect lamellas among themselvesFasten the base

Frame and headboard

After installing the base around the perimeter, the main back is installed, which is usually located at the head of the bed and three, the so-called czars. Screws or Euroscrews connect the elements together. Using the hexagon securely fasten the joints.

When the frame around the perimeter of the base is ready, begin to strengthen it. For this, power partitions are used, which are fixed to the tsars. Connecting elements can serve as metal corners or brackets. At the bottom of the frame, MDF panels or chipboard sheets are fixed. Material for the bottom of the structure is included and depends on the quality of the furniture.

Further to the longitudinal partitions or to the tsars are attached the legs of the bed. For the installation of legs, special platforms may be provided. After performing these operations, installation of the crossbeams and corners in the space between the drawbars and the longitudinal reinforcing partitions is started. Now you can begin to fix the main back at the head.

The assembly process of the structure must begin from the bottom up. This method will greatly simplify the assembly of the bed. In the process, check the correct installation of fasteners. Assemble the bed as shown in the instructions so that the lifting elements are arranged symmetrically. Otherwise, it can quickly fail.

In some models, mainly for cribs, a pendulum design is installed instead of legs. It can be longitudinal or transverse and is used for motion sickness of the baby. The rest is a light frame and a base of lamellas.

Make the frameWe create partitions for internal fillingWe make a frame under the mattressSheathed product foamThen with a cloth

Installation of the lifting gear

The lifting mechanism can be located both on the legs and on the back at the head. It depends on the type of bed model and manufacturer. According to the instructions, the lifting device is fixed to the frame panel with minimal backlash. Next, connect the lift with the upper base, align the gaps formed between the frame and the base, and tighten all the screws of the mechanism.

It is very important to carry out all the installation work of the lifting mechanism correctly so that the slightest inaccuracies and errors in the mounting do not interfere with the further operation of the unit and do not spoil the device. Check the working stroke of the lifting mechanism, if necessary, the parts are lubricated for silent operation. In the absence of malfunctions, handles are screwed to the upper base in order to conveniently use the design, and possible limiters. It remains only to lay the mattress in the base and you're done.

Along with lifting devices, there are also transformer mechanisms that extend an extra bed. Many will agree that it is not very convenient to have double assembled furniture in your room. Therefore, such transforming devices were invented that convert a single bed into a double bed in a few seconds. These models include a dolphin sofa bed and a eurobook. You can learn how to assemble and install such modules by receiving detailed assembly instructions from the video master class.

Making a bolt holeLift LockGazpatron mountConnection of internal mechanismsMounting support angles

Additional equipment

Bed selection should be approached with particular attention. It should serve as a relaxation area and decoration of the room. To create additional space for storing small items, it is ideal to install two chests of drawers or bedside tables next to the bed. A bedside dressing table in the bedroom will also look great.

There are models in which the base has an adjustable frame, allowing you to accommodate a mattress of a different size. Complementing the design of the headboard at the head with shelves, a complete storage system with advanced functionality is obtained. This design gives the furniture conciseness and does not clutter up the space of the room.

The legs fixed at the bottom of the bed are often replaced with rollers or wheels, which will make it possible to easily move upholstered furniture to another place and perform wet cleaning under the bed. When the structure is fully assembled, it can be covered with a specially-made soft cover for the size of the bed, which will decorate the berth and give it an aesthetic appearance.

Final stage

Finally, the assembly and installation of the lifting mechanism is completed. It is necessary to take the last step - carefully check the quality of fastening of all the connecting parts: tighten the screws and Euroscrews. Final inspection is an equally important stage of furniture assembly. In parallel, the horizontal, proportions of the structure and the correctness of the angles are checked.

Now the bed is equipped with drawers. Boxes regulate, achieving a smooth ride. If the adjustment is performed poorly, then the design of the box can after a short time give a skew, which will affect the appearance of the entire structure. At the very last moment, decorative elements and accessories are fastened.

The bed assembly diagram and video instructions greatly facilitate the installation process and show in detail how to properly assemble the bed. If the customer has high assembly requirements, it is best to contact experienced specialists.

Manufacturers of upholstered furniture offer the buyer a huge amount of their products. And although their appearance is diverse, but the principle of creation is no different. Any model is equipped with instructions that describe how to assemble a bed.

We tightly fix all the fittingsCheck boxes

Video

Watch the video: Plywood Co-Sleeper Part 2: Assembly (October 2024).

Leave Your Comment